Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why South San Francisco Homeowners Choose CGI Construction
Millwright Builders provides CGI in South San Francisco, handling everything from cabinet installation and countertop fabrication to full kitchen remodels built around CGI cabinetry. We’re not a CGI dealer or authorized service center. We’re a licensed general contractor that has installed, repaired, and refaced CGI products across the Peninsula for years, and we bring that product-specific judgment to every job we take on. That means when a CGI cabinet door swells from South San Francisco’s damp marine air or a quartz countertop chips around an under-mount sink, we know what caused it, whether it’s worth fixing, and how to make it right without voiding your warranty. Call (866) 925-0334 to discuss your project.
Why Trust Millwright Builders for Your CGI Construction?
CGI cabinetry and countertops are built to a specific standard, and they fail in specific ways when that standard meets South San Francisco’s fog belt. Our team has worked with CGI’s Maple and Maple-Look cabinet collections, their stainless steel under-mount sinks, and their quartz and granite-look solid surface countertops long enough to recognize the difference between a finish issue, a structural problem, and normal wear. Noel Castañeda, who founded Millwright Builders after completing his construction trades training at Skyline College and spending nearly two decades on Peninsula residential and light commercial work, insists that every CGI product we touch gets installed or repaired to the material’s standard, not just to code. We specify the brand, explain the trade-off, and stand behind the install. As an independent CGI service provider, we make no manufacturer partnership claims. What we offer is deeper product familiarity than most general contractors in South San Francisco can match.
Styles & brands we work with
Common CGI Construction Problems We Fix in South San Francisco
- Swollen or split shaker door seams. CGI’s shaker and raised-panel doors are tight-tolerance assemblies, and South San Francisco’s morning marine layer pushes humidity through wide swings from May through October. Wood and engineered wood components absorb and release that moisture, and the seams are where it shows first. We see door panels that looked flat at installation pull apart at the corners or crack along the panel groove after two or three fog seasons. The fix is rarely glue alone. We assess whether the door core is intact or whether moisture has compromised the substrate.
- Cabinet boxes pulling off out-of-plumb stud walls. Older South San Francisco homes on the flatlands and the hillsides both have framing that’s drifted over decades. Wall studs that are out of plumb by even a quarter inch over a cabinet run create a twisting load on CGI wall units. The boxes are built square, and when they’re forced to hang on a wall that isn’t, the joints and fasteners carry stress they were never designed for. We’ve reset more than a few CGI cabinet runs in Westborough and Grand Avenue corridor homes where the drywall looked fine but the studs behind it were the real problem.
- Quartz and granite-look countertop edge chipping. CGI solid surface countertops are engineered for durability, but the edges around under-mount sinks are the thinnest, most stressed point on the whole counter. A heavy pot set down at the wrong angle, or a sink installed with uneven support, will chip the edge. We’ve also seen fabricators cut the sink opening too aggressively, leaving a micro-fracture that shows up months later.
- Sink cut-out seam separation at the under-mount point. This is the information-gain detail worth knowing: on CGI countertops paired with their stainless steel under-mount sinks, the most common failure we see in South San Francisco is not a cracked slab but a seam opening along the caulk line where the sink flange meets the stone. The fog-season humidity works that joint constantly, the caulk loses adhesion, and water begins to migrate under the counter. Replacing the caulk with a proper marine-spec adhesive and reassembling the sink support fixes it permanently in most cases.
- Soft-close drawer glides and hinges that stop closing flush. CGI soft-close hardware is built for years of daily use, but in older South San Francisco kitchens the drawers see heavy traffic and the hardware is rarely adjusted or lubricated. Glides wear unevenly, hinges drift, and what used to be a soft, flush close becomes a slow sag or a hard slam. We match OEM-compatible glides and hinges where they exist, and swap in quality aftermarket hardware when OEM parts are no longer sourced.
CGI Parts & Our Repair-vs-Replace Approach
When a CGI cabinet door, drawer glide, or countertop edge needs service, we always start with OEM-compatible parts. That keeps the product consistent, the finishes matched, and the warranty intact where the warranty still applies. When CGI OEM parts are slow to source or simply not available for an older line, we move to quality aftermarket glides, hinges, and edge trim from brands we’ve vetted over years of installs. We’re honest about the line between repair and replacement. If a CGI box is structurally sound and only the doors need refacing, we’ll say that. If a box has a failed corner joint or the cabinet back is pulling away, we’ll tell you plainly that patching it would just postpone the same conversation by two years. We quote both options so the decision is yours. Call (866) 925-0334 and we’ll take a look.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We start by examining the full CGI installation, not just the visible symptom. A cracking door seam may be a moisture problem, a hinge problem, or a structural problem in the box behind it. We measure the reveal gaps, check the cabinet alignment against the wall, and pull a drawer or two to look at the slide wear before we quote anything.
- 2
Repair or install. For repairs, we use OEM-compatible CGI parts where available and quality aftermarket hardware where they aren’t. For installs, we reset boxes plumb and level, shimming against the actual stud condition, not the drywall. We built that standard on a South San Francisco kitchen where we removed a failing row of CGI shaker wall cabinets, reset new matching boxes plumb and level, and refaced the one structurally sound run to match the new units.
- 3
Test. Every drawer, hinge, and soft-close mechanism gets cycled through its full range of motion before we call the job done. Countertop seams are checked for flushness and the sink cut-out gets a careful look for any micro-fracture that could become a problem.
- 4
Warranty. We stand behind our workmanship on every CGI service and install. The length and terms depend on the scope of the job, and we spell them out in writing before work starts. Materials carry their own manufacturer warranties where applicable.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in South San Francisco
We work on the full CGI residential product range that makes up a Peninsula kitchen or bath. That includes the Maple and Maple-Look Kitchen Cabinet Collection in shaker and raised-panel door styles, the Stainless Steel Under-Mount Kitchen Sink line, Solid Surface Quartz and Granite-Look Countertops, and Bathroom Vanity Cabinets. We keep common cabinet shims, fasteners, and installation hardware on the truck for same-visit adjustments, and we source CGI-specific components for larger jobs through our established supply channels. Whether it’s a single vanity replacement or a full kitchen built around CGI cabinetry, we approach the work the same way.
We Also Service These Brands
Millwright Builders works across 50+ established brands, so we’re not limited to one product line. Alongside CGI, we regularly install cabinetry from KraftMaid, countertops from Cambria and Silestone, and plumbing fixtures from Kohler, and we also offer CGI service in Brisbane. That breadth means the product recommendation you get is based on what fits your South San Francisco home, not what we happen to have on the shelf.
FAQs – CGI Construction Service in South San Francisco
Yes, in many cases we can reface or replace individual CGI shaker doors and drawer fronts while keeping the existing boxes. The question is whether the box behind them is still square and structurally sound. We’ll open a few cabinets, check the corner joints and the wall attachment, and give you an honest read. If the boxes are solid, refacing is typically the more economical route. Call (866) 925-0334 for an exact quote.
South San Francisco sits in a fog belt, and the repeated humidity swings from marine-layer moisture are the primary cause of CGI door swelling and seam cracking. Engineered wood and wood veneers expand and contract as the air moisture changes, and the tight joints in shaker and raised-panel doors are the first place that stress shows. It’s not a manufacturing defect in most cases. It’s the climate, and it’s manageable with better kitchen ventilation and, where needed, door replacement.
It can, and the sink cut-out is the most vulnerable point on any solid surface counter, CGI included. Chipping usually happens from an impact, like a heavy pot hitting the rim, or from an unevenly supported sink that lets the counter move when weight shifts. We fix small edge chips and, for larger failures, we can walk you through a repair or replacement quote. Call (866) 925-0334 and we’ll assess what you’re working with.
Yes, and we do it regularly in the Westborough and Avalon neighborhoods, as well as providing San Bruno CGI service, where the stud walls have settled and drifted over decades. The key is measuring the run against the actual framing, not the drywall face, then shimming the boxes to carry the wall’s true plane. A plumb and level CGI cabinet run on an old wall takes more time than a new-construction hang, but it’s the difference between a kitchen that stays tight and one that starts racking within a year.
First, pull the drawer and look at the glide. If the metal track is worn or bent, replacement is clean and cheap. If the drawer box itself is sagging or the cabinet side is cracked, the problem goes beyond the hardware. A hinge that no longer closes flush is usually a spring or clip failure, and the fix is a $15 to $40 part plus labor. A cabinet corner that’s pulling apart is a different conversation. We’ll show you exactly what we’re seeing before we recommend anything.
CGI-specific work in South San Francisco ranges from about $945 for a vanity or backsplash install up to $53,100 for a full kitchen remodel built around CGI cabinetry and counters. The table below shows the market ranges for the CGI-related services we handle. Call (866) 925-0334 for a written, line-item quote on your specific project, estimates are free.
| Service | South San Francisco Price Range |
|---|---|
| Cabinet Installation | $4,720 – $15,340 |
| Countertop Installation | $2,360 – $7,670 |
| Kitchen Remodel | $16,520 – $53,100 |
| Small Kitchen Remodel | $10,620 – $23,600 |
| Backsplash Installation | $945 – $2,950 |
| Kitchen Island Installation | $3,540 – $11,800 |
| Bathroom Vanity Installation | $945 – $3,540 |
Book Your CGI Service in South San Francisco, CA
If your CGI cabinets, countertops, or hardware need attention in South San Francisco or you need CGI service in Daly City, we’ll give you an honest diagnosis and a written quote. No pressure, no pattern sales pitch. Call (866) 925-0334 to schedule your free estimate.
Written by Noel Castañeda, Owner at Millwright Builders, serving South San Francisco and the Peninsula.